Feiyiya Inclined Plate Clarifiers Use Gravity & Innovative Engineering
A gravity clarifier is the most economical method of removing solids from liquids, using natural gravity as the source of energy and it is free. A clarifier simply provides a non-turbulent zone where heavier than liquid solids, suspended by turbulence, are given sufficient time to settle to a quiescent surface. The HEI inclined plate clarifiers are compact units with multiple layers of settling area utilizing less than 25% of the floor space required by conventional clarifiers.
Principle of Clarifiers
A particle carried forward by the velocity of the liquid flow must settle at a rate that allows it to reach the bottom before passing through the clarifer. Thus, particles beginning at a point [a" must traverse some route lying between ab and ab` in order to avoid being carried over the outlet.
If V is the horizontal velocity of the liquid, S the solids particle vertical settling velocity, L the length of the settling device, and D its depth, then particles entering at point A will settle to the bottom of the device only if V does not exceed: S(L/D)Since Vmax / S = L / D then, Vmax = S (L / D)
Inclined plate clarifier, Lanmei inclined plate clarifier, Inclined Tube Settler,High-Efficiency Inclined Tube Wuxi Feiyiya Environmental Protection Technology Co., Ltd. , https://www.feiyya.com
Main Features:
- Tig & MMA welding modes.
- Portable, energy-saving, and high efficiency.
- Easy arc starting, minimal spatter, low noise, stable arc welding, deep penetration, and aesthetically pleasing weld seams.
- Automatic compensation for voltage fluctuations, capable of operating under input voltage fluctuations.
- High efficiency and better energy-saving compared to traditional welders.
- DC TIG arc welding can be used for all types of metals, offering a reasonable price with high quality.
Steel MOSFET Inverter TIG Welding Machinery Specification
Model
TIG-200P ACDC
TIG-250P AC/DC
TIG-315P AC/DC
Type
IGBT
Rated input voltage (V)
single phase 220V±15%
three phase 380V±15%
Rated frequency (Hz)
50/60
Rated input current (A)
24
9.6
11.4
No-load voltage (V)
56
45
45
Output current (A)
10-160
10-250
10-280
Pre-flow time (s)
0-2
Gas delay time (s)
2-10
Duty ratio
20%-80%
Decay time (s)
0-5
Duty cycle (%)
60
No-load loss (W)
60
Arc starting
high frequency arc starting
Efficiency (%)
85
Power factor
0.93
Insulation grade
F
Protection grade
IP21
Net weight (KG)
23.4
31.2
31.2
Dimension of packing (mm)
625×400×505
625×400×505
625×400×505
Steel MOSFET Inverter TIG Welding Machinery Accessories: earth clamp×1pcs, cable joint×1pcs, grounding cable×3meters, TIG torch×1set
Steel MOSFET Inverter TIG Welding Machinery Selection Guide
Material
Sheet thickness (mm)
Tungsten diameter (mm)
Current range(A)
Model
Carbon steel, stainless steel, low alloy steel
0.3-6
1.6-2.4
20-175
TIG-160
0.3-10
0.8/1.0
20-190
TIG-200
0.3-12
1.0/1.2
20-220
TIG-250
0.3-12
2.5-3.2
5-400
TIG-400P
Copper
0.3-14
2.5/3.2/4.0
5-500
TIG-500P
0.5-5.0
2.5-3.2
5-400
TIG-400P
0.5-60
2.5/3.2/4.0
5-500
TIG-500P
Carbon steel
Stainless steel
Low alloy steel
Aluminum
1.5-5
2.5/3.2
5-200
TIG-200P AC/DC
1.5-5
2.5/3.2
5-250
TIG-250P AC/DC
1.5-5
2.5/3.2
5-315
TIG-315P AC/DC
Package & Shipping
Packaging Details: Carton package with inside plastic bag and foam / wooden packing / Packing according to customers requirements.
Delivery: within (25-30) days after confirmation of the deposit.
Company Information
Zhejiang ST welding machine have a number of inventions and patents, covering IGBT module, single-tube IGBT, MOSFET three series of welding and cutting equipments.
Continuous innovation, focus on the quality, integrity managements and common development are the pursuit of Zhejiang ST Group. To provide customers with high quality, reliable products and services are the eternal principle.
Our products are widely used in chemical, construction, light industry, machinery manufacturing, shipbuilding, metallurgy, automobile manufacturing, aerospace and other professional fields.
FAQ
Therefore, the velocity at which a horizontal clarifying device may be operated successfully is directly proportional to its length and inversely proportional to its depth.
This analysis applies to multiple horizontal plate units also. The spacing between plates is usually a few inches as opposed to a depth of several feet in a horizontal tank; therefore, [settling-out" times are dramatically reduced. The flow must be non-turbulent to prevent settled solids from being re-entrained within the moving liquid. Small plate spacing and a large surface area permits laminar flow at higher velocities than large horizontal tanks would allow.
Horizontal clarifying devices become self-flushing if they are inclined at an angle which exceeds the angle of repose of the settled solids. In such cases, flow enters the lower end of the device where settling particles move to the floor eventually sliding back out the entrance. Clear effluent leaves the top of the device.
However, when the device is inclined, the furthest settling particles no longer fall through distance D but some longer distance D`. This new longer settling distance D` is related to D by the relation: D = D` cos Ø.
Theta [Ø" is the angle, the device is inclined to the horizontal plane. Thus settling distance is increased by the factor: 1/cos Ø In the case where Ø = 60º, 1/cos Ø = 2.
The maximum settling distance is twice the distance between the plates. It is apparent then that the lower the angle of inclination, the smaller the settling distance. However, the angle of inclination must exceed the angle of repose of the solids to be separated. The previous equation may be modified to express the cosine of an inclined plate clarifying system as:
Vmax = L / (D / cosØ) (s) = L·cosØ / D (s)
Inclined Plate Clarifiers
A reduction of the required floor space is acquired by diminishing the separation between the horizontal plates to a few inches and stacking the settling surfaces. Inclining the plates to provide self flushing, 45º for heavy particles and 60º for light particles, reduces the available horizontal projected area (effective settling area) by a factor equivalent to the cosine of the angle. The surface area diagram (below) graphically compares the floor space requirements of an HEI inclined plate clarifier with the equivalent horizontal projected settling area.
Settling Rate
The settling rate for a specific solids should be determined by standard laboratory tests. Light particles, such as metal hydroxides, usually require a design parameter of 0.25 – 0.50 gallons per minute per square foot of horizontal projected area. These low density solids require the inclined plates to be set at a 60º angle to induce the particles to slide down the plate. Heavier particles (such as sand that easily flow) will readily slide from plates set at a 45º angle.
Maximum flow rate of an inclined plate clarifier is based on the flow rate per unit of a horizontally projected surface area. Retention time in the clarifier is not a design criteria. However, attaining optimum performance requires the prudent design to recognize several additional, very important factors.
Aluminum IGBT Inverter TIG Welding Machinery TIG-250p AC/DC
Aluminum IGBT Inverter TIG Welding Machinery TIG-250P AC/DC
Inclined plate clarifier
1. Q: Are you a factory or trading company?
A: We are a factory; our main products are welding machines and voltage regulators/transformers.2. Q: How many days for mass producing?
A: It will cost 30 days after confirming the order.3. Q: Can you do OEM?
A: Yes, we can do OEM/ODM.